Alpine Navigation Radio Owner's Manual Page 127

  • Download
  • Add to my manuals
  • Print
  • Page
    / 151
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 126
125-EN
Navigation
Audio/Visual
Symptom Cause Solution
The present vehicle position
cannot be measured correctly.
The vehicle position changed after the ignition
was switched off.
Movement on a ferry boat
Rotation of a parking lot turntable
Movement by tow truck
Drive the vehicle in an area of good GPS reception to
allow the unit to recalibrate it self.
Vehicle position is displayed
incorrectly on the screen.
Poor satellite configuration. Move to a location where GPS satellite reception is
easy.
Measurement is 2 dimensional.
The Speed Sensor Lead is not connected
properly.
Connect it properly. (See page 140.)
The sound guide is not outptting. The sound guide is set to “Off”. Turn up the volume. (See page 92.)
The sound guide is too loud/low. The guide sound is not adjusted. Adjust the volume. (See page 92.)
The Vehicle position icon is not
displayed. Or, The map is not
scrolled after starting to drive.
A map other than the Current Vehicle Position
Map is set.
Press <NAV> to display the Current Vehicle Position
Map. (See page 24.)
Unable to display a map less than
200 m (200 yards) scale.
The map data on the SD card is corrupted. Consult your nearest Alpine dealer.
Symptom Cause Solution
Unable to receive stations. No antenna, or open connection in the antenna
cable.
Make sure the antenna is properly connected; replace
the antenna or cable if necessary.
Unable to tune stations in the seek
mode.
You are in a weak signal area. Make sure the tuner is in DX mode.
If the area you are in is a primary signal area,
the antenna may not be grounded and
connected properly.
Check your antenna connections; make sure the
antenna is properly grounded at its mounting location.
The antenna may not be the proper length. Make sure the antenna is fully extended; if broken,
replace the antenna with a new one.
Broadcast is noisy. The antenna is not the proper length. Extend the antenna fully; replace it if it is broken.
The antenna is poorly grounded. Make sure the antenna is grounded properly at its
mounting location.
The station signal is weak and noisy. If above solution does not work, tune in another station.
Disc playback sound is wavering. Moisture condensation in the disc Module. Allow enough time for the condensation to evaporate
(about 1hour).
Disc insertion not possible. A disc is already in the DVD player. Eject the disc and remove it.
Take out the currently inserted disc, and then insert a
new disc. (See page 18.)
The disc is being improperly inserted. Insert the disc correctly. (See page 18.)
Unable to fast forward or backward
the disc.
The disc has been damaged. Eject the disc and discard it; using a damaged disc in
your unit can cause damage to the mechanism.
Disc playback sound skips due to
vibration.
Improper mounting of the unit. Securely re-mount the unit.
Disc is very dirty. Clean the disc.
Disc has scratches. Change the disc.
The pickup lens is dirty. Do not use a commercial available lens cleaner disc.
Consult your nearest ALPINE dealer.
Disc playback sound skips without
vibration.
Dirty or scratched disc. Clean the disc; damaged disc should be replaced.
CD-R/CD-RW/DVD-R/DVD-RW/
DVD+R/DVD+RW playback not
possible.
Close session (finalisation) has not been
performed.
Perform finalisation and attempt playback again.
Error displays. Mechanical error. Press . After the Error disappears, insert the disc
again. If the abovementioned solution does not solve
the problem, consult your nearest Alpine dealer.
Page view 126
1 2 ... 122 123 124 125 126 127 128 129 130 131 132 ... 150 151

Comments to this Manuals

No comments