Alpine PDX-F6 Owner's Manual Page 3
- Page / 11
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
CD
Top
Cover/
Couvercle
superieur/
Tapa superior
Self-Tapping
Screw
(M4 x 36)/
Vis auto-
taraudees/
Tornillos
autorroscantes
Ground Lead/
Conducteur de
mise
ilia
terre/
Cable de tierra
Hole/
Trous/
Agujeros/
ACCESSORIES
• IMPORTANT
Please record
the
serial
number
of
your unit
in
the
space provided here and keep it as a permanent
record. The serial number plate is located on the rear
of the unit.
SERIAL
NUMBER: _
:~~i~~~i:g~
~~~~N...,IC."....,IA...,N...,:-------
PLACE OF PURCHASE:
SPECIFICATIONS
SERVICE CARE
• IMPORTANT NOTICE
This Amplifier has been type tested and found to
comply with the limits for a Class B computing device
in
accordance with the specifications
in
Subpart J
of
Part
15 of FCC Rules. This equipment generates
and
uses
radio frequency energy, and
it must be installed and
used properly
in
accordance with the manufacturer's
instructions.
•
For
European
Customers
Should you have any questions about warranty, please
consult your store of purchase.
•
For
Customers
in
other
Countries
IMPORTANT NOTICE
Customers who purchase the product with which this
notice is packaged,
and
who make this purchase
in
countries other than the United States
of
America and
Canada, please contact your dealer for information
regarding warranty coverage.
NOTE:
•
For
product improvement. specifications and design are :mbjecr to change without
IlOtice.
POX·F6 POX·F4
RMS Continuous Power (at 14.4 V)
• Per channel into 4 ohms
150Wx4 100Wx4
• Per channel into 2 ohms
150Wx4
100Wx
4
• Bridged into 4 ohms
300Wx2
200Wx2
THO+N (Reference: 10 W / rated power into 4 ohms)
0.003
% / 0.05 %
SIN Ratio (IHF A Weighted, Reference: rated power into 4 ohms)
116 dBA 115 dBA
SIN Ratio (IHF A Weighted, Reference: 1 W into 4 ohms) 94 dBA
95dBA
Input Impedance
10k ohms
Frequency Response (Reference: 1 W into 4 ohms)
5 Hz - 100 kHz / 0 dB - -3 dB
Crossover Frequency
(Variable,
L.P.F
/ H.P.F / OFF Selectable)
• 1/2 ch
30
Hz-
400
Hz
(-12 dB / oct)
• 3/4 ch
30 Hz - 400 Hz (-12 dB / oct)
Input Sensitivity (V / at 10k ohms)
0.2 V - 4.0 V with Input Level
Dimensions
• Width
257.0 mm (10-1/8")
• Height
50.8 mm (2")
• Depth
192.0 mm (7·9/16")
Weight
2.88
kg
2.87
kg
Fig.
1
Fig.
2
CD
CD
CD
..
CD
Machine Screw
(M3 x
7)/
Vis mecanique/
Tornillo
mecanico
• Stacking Plate (PDX-F6 Only).. . 2
• Machine Screw (M3 x 7) (PDX-F6 Only)
..
.
.4
• Machine Screw (M4 x 24) (POX-F6
Only)..
..
4
• Self-Tapping Screw (M4 x 36) 4
• Battery Connector 1
• Speaker Connector:.. . 4
• Hexagon Wrench (Large/Small) 1 SET
INSTALLATION (Fig. 1 - Fig. 4)
2
® Stacking Plate/
Plateau
d'empilement!
Placa de
apilamiento
Fig.
3
-
CD
Machine Screw
(M4 x 24)/
Vis mecanique/
Tornillo
mecanico
Second unit!
Deuxieme unite/
Segunda unidad
First unit!
premiere unite/
Primera unidad
Fig.
4
With this series of amplifiers, up to three units can be stacked together
in
a typical installation. Depending on the
number
of
units you wish to install, refer to instructions A to C below.
&'CAUTION
•
Caution
on
connection
terminals/parts
• Keep electrically conductive objects away from the unit's terminals/parts (power terminals, fuses, speaker
output terminals, RCA connectors, etc.). Doing
so
prevents a possible short circuit and
damage
to the unit.
Note:
• Stack installation should always be parallel to the vehicle
floor
-
do
not install at an iI/cline. sitch as leaning agaiflSt a
vertical slliface.
as
this will invalidate your warranty.
Preparation for installation
1.
Using the amplifier
as
a template, mark the four screw locations.
2.
Make sure there are no objects behind the surface that may become damaged during drilling.
3.
Drill the screw holes.
4.
Position the PDX-F6/F4 over the screw holes, and secure with four self-tapping screws.
NOTE:
•
To
securely connect the ground lead, t/se
all
already iI/stalled screw 011 the metal part
oIthe
vehicle (marked
*).
Be sure
this is a good grot/nd
by
checking continuity
to
the battery
(-)
terminal.
As
much as possible connect all equipmell1 to the
same ground poillt. These pmcedure.\· will help eliminate noise.
A.
Single unit installation
1.
Position the unit over the screw holes you prepared earlier.
2. Remove the Top Cover by inserting a flat-tipped instrument (such
as
a panel removal tool
or
slotted
screwdriver) into the 2 notches of the unit (marked A). II removal is still not possible, bend the Top Cover and
remove
the
tabs on both sides. Refer to Fig.
1.
3.
Fasten the unit down with the four self-tapping screws (M4 x 36, supplied).Refer to Fig. 2.
4. Attach the Top Cover.
B.
Stack installation
01
two units
1.
Firstly, securely install one unit,
as
described
in
steps 1-3 of A above.
2. Attach the Stacking Plates
(*)
on the first unit with Machine Screws
M3
x 7(*). Refer to Fig. 3.
3. Stack the second unit on
top
of
the installed unit.
4. Attach the second unit with four Machine Screws
M4
x 24 (*). Refer to Fig. 4.
5. Attach the Top Cover to the second unit.
C.
Stack installation
01
three units
1.
Firstly, securely install
the
first two units firmly
as
described in steps 1 to 4
of
B above.
2. Next, install the third unit
as
described for the second unit
in
B above. With this, stack installation of the 3
units is completed.
*PDX-F6: Supplied.
PDX-F4: Supplied with the stack illstallation unit.
Related products and manuals for Car audio amplifiers Alpine PDX-F6
(20 pages)
(2 pages)© 2020, manymanuals.com. All rights reserved. | 0.942 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals