Alpine TDM-7590R Owner's Manual download pdf (Page 24)

22-EN

Installation and Connections

Before installing or connecting the unit, please

read the following and pages 2 and 3 of this

manual thoroughly for proper use.

Warning

MAKE THE CORRECT CONNECTIONS.

Failure to make the proper connections may result in fire

or product damage.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE

GROUND.

(Check with your dealer if you are not sure.) Failure to do

so may result in fire, etc.

BEFORE WIRING, DISCONNECT THE CABLE FROM

THE NEGATIVE BATTERY TERMINAL.

Failure to do so may result in electric shock or injury due

to electrical shorts.

DO NOT SPLICE INTO ELECTRICAL CABLES.

Never cut away cable insulation to supply power to other

equipment. Doing so will exceed the current carrying

capacity of the wire and result in fire or electric shock.

DO NOT DAMAGE PIPE OR WIRING WHEN

DRILLING HOLES.

When drilling holes in the chassis for installation, take

precautions so as not to contact, damage or obstruct pipes,

fuel lines, tanks or electrical wiring. Failure to take such

precautions may result in fire.

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR

STEERING SYSTEMS TO MAKE GROUND

CONNECTIONS.

Bolts or nuts used for the brake or steering systems (or

any other safety-related system), or tanks should NEVER

be used for installations or ground connections. Using

such parts could disable control of the vehicle and cause

fire etc.

KEEP SMALL OBJECTS SUCH AS BOLTS OR

SCREWS OUT OF THE REACH OF CHILDREN.

Swallowing them may result in serious injury. If

swallowed, consult a physician immediately.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT

HINDER VEHICLE OPERATION, SUCH AS THE

STEERING WHEEL OR GEARSHIFT.

Doing so may obstruct forward vision or hamper

movement etc. and results in serious accident.

Caution

HAVE THE WIRING AND INSTALLATION DONE BY

EXPERTS.

The wiring and installation of this unit requires special

technical skill and experience. To ensure safety, always

contact the dealer where you purchased this product to

have the work done.

USE SPECIFIED ACCESSORY PARTS AND INSTALL

THEM SECURELY.

Be sure to use only the specified accessory parts. Use of

other than designated parts may damage this unit

internally or may not securely install the unit in place.

This may cause parts to become loose resulting in hazards

or product failure.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR

PINCHED BY A SHARP METAL EDGE.

Route the cables and wiring away from moving parts (like

the seat rails) or sharp or pointed edges. This will prevent

crimping and damage to the wiring. If wiring passes through

a hole in metal, use a rubber grommet to prevent the wires

insulation from being cut by the metal edge of the hole.

DO NOT INSTALL IN LOCATIONS WITH HIGH

MOISTURE OR DUST.

Avoid installing the unit in locations with high incidence

of moisture or dust. Moisture or dust that penetrates into

this unit may result in product failure.

Precautions

• Be sure to disconnect the cable from the (–) battery post

before installing your TDM-7590R. This will reduce any

chance of damage to the unit in case of a short-circuit.

• Be sure to connect the colour coded leads according to

the diagram. Incorrect connections may cause the unit to

malfunction or damage to the vehicle's electrical system.

•

When making connections to the vehicle's electrical system,

be aware of the factory installed components (e.g. on-board

computer). Do not tap into these leads to provide power for

this unit. When connecting the

TDM-7590R

to the fuse box,

make sure the fuse for the intended circuit of the

TDM-

7590R

has the appropriate amperage. Failure to do so may

result in damage to the unit and/or the vehicle. When in

doubt, consult your ALPINE dealer.

• The TDM-7590R uses female RCA-type jacks for

connection to other units (e.g. amplifier) having RCA

connectors. You may need an adaptor to connect other

units. If so, please contact your authorized ALPINE

dealer for assistance.

• Be sure to connect the speaker (–) leads to the speaker

(–) terminal. Never connect left and right channel

speaker cables to each other or to the vehicle body.

IMPORTANT

Please record the serial number of your unit in the

space provided below and keep it as a permanent

record. The serial number plate is located on the

bottom of the unit.

SERIAL NUMBER:

INSTALLATION DATE:

INSTALLATION TECHNICIAN:

PLACE OF PURCHASE:

1 ... 23 24 25 26 27 28

Comments to this Manuals

No comments

Alpine TDM-7590R Owner's Manual Page 24

Comments to this Manuals

Related products and manuals for Receiver Alpine TDM-7590R