Alpine DVA-9861Ri User Manual download pdf (Page 42)

41-EN

01GB05DVA9861Ri.fm

ALPINE DVA-9861Ri 68-04123Z62-A (EN)

Setting Bass Focus

Using the previously specified delay number (time difference) allows

you to set a time difference between the front-rear/left-right speakers.

Namely, it enables a time correction based on your preference. With an

initial delay of 0.05 ms for each of the 0 to 400 steps, audible time

correction can be achieved.

Check that Defeat mode is off (page 25).

Press and hold TA for at least 2 seconds.

The audio processor control mode is activated.

Select the BASS SOUND mode by pressing TA.

Select BASS FOCUS by pressing or , then

press MODE.

Press MODE to select the front/rear/left/right

speaker.

Turn the Rotary encoder to set the front/rear and

left/right speakers.

To set other channels (speakers), repeat steps 5 and

When the setting is complete, press and hold TA for

at least 2 seconds.

The unit returns to the normal mode.

• Any setting in Bass Focus is applied in time correction, too.

• When the setting is complete, it is recommended to store the setting

contents. For storing, refer to page 44.

Speaker Setup

The PXA-H700 or PXA-H701 can be set according to the playable

frequency range of your speakers.

Check the playable frequency range of the speakers (not including the

subwoofer) before performing this operation to verify whether the

speakers can play low frequencies (of about 80 Hz or less).

• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding

or switching the audio channel of this unit while making this

adjustment. The setting is cancelled if Decode mode is switched.

Check that Defeat mode is off (page 25).

Press and hold TA for at least 2 seconds.

The audio processor control mode is activated.

Select the SP SETUP mode by pressing TA

repeatedly.

Select the speaker by pressing the MODE.

Select the speaker characteristic by turning the

Rotary encoder.

(Subwoofer is set to ON/OFF only)

Repeat steps 4 and 5 to set each speaker.

When the setting is complete, press and hold TA for

at least 2 seconds.

The unit returns to the normal mode.

• If the centre speaker is turned “OFF,” the centre channel’s audio

signals are added to the audio signals output from the front speakers.

• If you set the speaker response to “OFF,” also set the speaker setting

to “OFF.” (page 37)

• Perform the setup for all the speakers (“Front,” “Center,” “Rear”

and “Subwoofer”). If not, the sound may not be balanced.

• When centre is set to “OFF”, the setting is ineffective even if centre

is set with this function.

• Through changing the settings on each speaker, a change in the

output of the other speakers may occur due to the setting

requirements.

• When using the PRO LOGIC II, if the rear speaker is set to

“LARGE”, then there will be no output from the subwoofer.

• When the setting is complete, it is recommended to store the setting

contents. For storing, refer to page 44.

Setting of Dolby Digital

The test tones help to make the volume adjustments of the different

speakers. When levels are equal, a strong sense of presence can be heard

from the different speakers at the listening position.

• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding

or switching the audio channel of this unit while making this

adjustment. The setting is cancelled if the decode mode is switched.

Check that Defeat mode is off (page 25).

Press and hold TA for at least 2 seconds.

The audio processor control mode is activated.

Select the MULTI CH SETUP mode by pressing TA

repeatedly.

Select OUTPUT LEVEL by pressing or ,

then press MODE.

OFF*

: When no speaker is connected.

SMALL: When a speaker that cannot play low

frequencies (80 Hz or less) is connected.

LARGE*

: When a speaker that can play low frequencies

(80 Hz or less) is connected.

It is not possible to set the front speakers to “OFF”.

If the front speakers are set to “SMALL”, the rear and

centre speakers cannot be set to “LARGE”.

Adjusting the speaker levels

01GB00DVA9861Ri.book Page 41 Wednesday, December 7, 2005 12:00 PM

1 2 ... 37 38 39 40 41 42 43 44 45 46 47 ... 75 76

Comments to this Manuals

No comments

Alpine DVA-9861Ri User Manual Page 42

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Alpine DVA-9861Ri