Alpine 611 User Manual

AlpineTMNE 5007Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545 Visit our web site at:www.swing-n-slide.comor call us at1-800-88

104'' x 4'' x 96''(4)2'' lag screws43-1/4''A. Frame Construction1. Measure and position brackets on

1182-1/2''82-1/2''GAP (this side)GAP (this side)Wrap-Loc opening must be positionedas shown on in these locations belowfor later u

12A. Frame Construction (cont.)3. Install upper 2'' x 4'' boards. Edges are to be flushwith 4'' x 4’’s.Fig. 32'&apo

13Fig. 42'' x 4'' x 43''5/4'' x 6'' x 43''2'' x 4'' x 43''5/

14Fig. 5(4)4'' x 4'' x 35-1/2''(6)2'' lag screws(3 each Cup-Loc)(3) 2-1/2''screws/nailsA. Frame Cons

15Fig. 8Fig. 72'' x 4'' x 12''2'' x 4'' x 45''2'' x 4'' x 12'&apo

16Fig. 9(7) 5/4'' x 6'' x 43''5/4'' x 6'' x 36''2-1/2'' screws/nails(2 per joint

17Fig. 10aFig. 11Fig. 10Fig. 11a4'' x 4'' x 29-3/4''9-1/8'' to edgeSecure 4''x4'' uprights

18Fig. 12Fig. 132'' x 4'' x 55''2'' x 4'' x 55''E. Install Upper Rail Boards1. Install upp

1931-3/4''bottom of baseFig. 145/4'' x 6'' x 55''(4) 2-1/2'' screws/nailsG. Install Protective Barri

2Important! Additional Safety Instructions for all Swing-N-Slide Playground Equipment. Save this instruction sheet in the event the manufacturer need

20Fig. 15H. Install Accessory Brackets1. Secure Shelf-Loc brackets onto Wrap-Loc as shown in(Fig. 15), (Fig. 15a), (Fig. 16). Fig. 15a2'' La

21Fig. 17aFig. 17I. Install Accessory 4x41. Work 4'' x 4'' into brackets as shownin (Fig. 17).2. Secure brackets (Fig. 17a).2&apos

22NOTE: Lay the lumber on a flat surfacebefore beginning laminated beam assembly.NOTE:Attach one end of the beam with three 2-1/2'' screws.

23Fig. 19J. Swing Beam Drill Locations1.Use a 3/8'' drill bit to drill a 3/8’’ hole throughthe beam at each location shown in (Fig. 19)2. T

24Fig. 19aJ. Swing Beam Drill Locations1. Tap T-nut into 3/8’’ hole as shown in (Fig. 19a)Note: If using Laminated Swing Beam, make sure t-nut teeth d

25Align the edges of the 4" x 4" legswith the edges of EZ Frame Bracket94-1/2"24-1/2"EZ FrameBracket4" x 4" x 96'&

26Cantilever beamT-nut2-1/2''screws/nailsHex BoltWasherL. A-Frame Assembly cont.1. Attach A-Frame beam to Swing Beam using (2) hex bolts and

27Fig. 24aView from Deck2'' Lag screwx 8 (each bracket)25-1/2''L. A-Frame Assembly cont.1. Position Split-Brackets on 4'&apos

28Fig. 25Fig. 26(6) 5/4'' x 6'' x 30''L. Barrier Boards1. Install 5/4'' x 48'' barrier boards evenl

2916-1/4''2'' x 4'' x 36''2'' x 4'' x 55''2'' x 4'' x 36&apo

SAFETY INSTRUCTIONSINSTRUCCIONES DE SEGURIDADINSTRUCTIONS CONCERNANT LA SÉCURITÉREQUIRED SAFETY INSTALLATION INSTRUCTIONS• Once the unit is completel

30(6) 1-1/4'' screws or4D nails(3)2-1/2'' screws/nailseach side(2)2-1/2'' screws/nailseach sideFig. 3123 1/42 3/414 7/8

31Q. Slide Installation.1. Install as shown in (Fig. 33)Important: Do not use hardware providedwith slide. Use Truss head screwsincluded with Kit.Fig.

32Fig. 34Fig. 36Fig. 37R. Final Assembly.1. Hold the swing seat vertically and insert uncoated chainsthrough the channels on the bottom of the swing s

331-1/2" lag boltmetal strapAnchor-ItstakeFlat WasherS. Anchor-It Installation (optional).Instructions for Anchoring Swing•N•Slide Activity Cente

3434LUMBER REQUIRED(sold separately)QTY DESCRIPTION2 5/4" x 6" x 10'INSTRUCTIONS1.Cut one 5/4" x 6" x 72-3/4". Cut one 5

35Fig. 39Fig. 39aFig. 39b(2) 2-1/2'' screws/nails(Per joint)(4) 2-1/2'' screws/nails(Underneath)2'' x 4'' x 43

© PlayCore Inc. 2007 Printed In USA LA 5615Questions???...Call our Customer Service Departmentat 1-800-888-1232

4(6) 1-1/4'' screws(2) 5/16'' flat washers(4) Bottom Beam Clamps(slotted) (6) Tarp Washers(4) 1/4'' flat washers(6) T-

5(2) Swing Seatsweight limit: 115 lbs.(4) Swing HangersTHIS PRODUCT ISINTENDED FOR USEBY CHILDREN FROMAGES 2-10 YEARSFor Home / ResidentialUse ONLY121

6(287) 2-1/2'' screws(56) 2'' screws'e ALPINEREQUIRED HARDWARE(Not Included)(64) 1-1/4'' screws

7ALPINE

8(3) 2-1/2'' screws or nailsApply 2 1/2" screws/nails to the 2"x4" boards when attaching to 4"x4" uprights.(4) 2-1/

9-Understanding how the Bracket System WorksCup-LocGAPIntroduction to the Bracket system1.ALWAYSUse 2'' lag screws on all brackets. 2. Brack