Alpine DVA-9861Ri User Manual download pdf (Page 43)

42-EN

01GB05DVA9861Ri.fm

ALPINE DVA-9861Ri 68-04123Z62-A (EN)

Press MODE to select the speaker to be adjusted.

The test tone is produced by the selected speaker.

Adjust the output level by turning the

Rotary encoder.

Adjust each volume level for optimum balance by

repeating steps 5 and 6.

• The adjustment range for the different speakers is –10 dB - +10 dB.

• Adjust based on the front speakers.

When the setting is complete, press and hold TA for

at least 2 seconds.

The unit returns to the normal mode.

• If a speaker is set to off mode, that speaker’s level adjustment cannot

be made. Refer to “Speaker Setup” (page 41).

• When the setting is complete, it is recommended to store the setting

contents. For storing, refer to page 44.

This function mixes the front channel audio signals to the audio signals

output from the rear speakers, improving the sound in the vehicle’s rear

seat.

• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding

or switching the audio channel of this unit while making this

adjustment. The setting is cancelled if the Decode mode is switched.

Check that Defeat mode is off (page 25).

Press and hold TA for at least 2 seconds.

The audio processor control mode is activated.

Select the MULTI CH SETUP mode by pressing TA

repeatedly.

Select REAR MIX by pressing or , then

press MODE.

Select REAR MIX ON/OFF by turning the

Rotary encoder.

If ON is selected, press MODE.

If ON is set, the audio signal which is output from the rear

speaker is mixed to the front audio signal.

After setting to ON, turn the Rotary encoder to

adjust the level (LEVEL).

The level can adjusted in five steps: –6, –3, 0, +3 and +6.

The higher the level, the more bass is output from the rear

speakers. (The effect differs according to the software

(DVD, etc.).)

When the setting is complete, press and hold TA for

atleast 2 seconds.

The unit returns to the normal mode.

• This adjustment is ineffective when the rear speaker setup setting is

set to “OFF.”

• For linear PCM signals, the voice is output from the rear speaker

regardless of the REAR FILL and REAR MIX setting.

• When the setting is complete, it is recommended to store the setting

contents. For storing, refer to page 44.

In most installations, the centre speaker must be placed directly between

the front passenger and driver. Using this function, the centre channel

information is distributed to the left and right speakers. This creates an

acoustic image simulating a centre speaker directly in front of each

listener. Adjusting the centre width in PL II MUSIC (see “Using the Pro

Logic II Mode” page 43), makes this function ineffective.

• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding

or switching the audio channel of this unit while making this

adjustment. The setting is cancelled if the Decode mode is switched.

Check that Defeat mode is off (page 25).

Press and hold TA for at least 2 seconds.

The audio processor control mode is activated.

Select the MULTI CH SETUP mode by pressing TA

repeatedly.

Select BI-PHANTOM by pressing or , then

press MODE.

Select BI-PHANTOM ON/OFF by turning the

Rotary encoder.

If ON is selected, press MODE.

If ON is set, the soundstage created is as if you are

positioned directly in front of the centre speaker by

distributing the centre speaker sound left and right.

After setting to ON, turn the Rotary encoder to

adjust the level (LEVEL).

The level can be adjusted within the range of –5 to +5. The

higher the level, the more the position of the centre speaker

is shifted to the sides.

When the setting is complete, press and hold TA for

at least 2 seconds.

The unit returns to the normal mode.

• This adjustment is effective when the setting of the centre speaker to

SMALL or LARGE in the speaker setup settings.

• This adjustment is ineffective when the speaker is set to CENTER

“OFF” in “Setting the Speakers” (page 37).

• When the setting is complete, it is recommended to store the setting

contents. For storing, refer to page 44.

Mixing bass sound to the rear channel

Adjusting the acoustic image

01GB00DVA9861Ri.book Page 42 Wednesday, December 7, 2005 12:00 PM

1 2 ... 38 39 40 41 42 43 44 45 46 47 48 ... 75 76

Comments to this Manuals

No comments

Alpine DVA-9861Ri User Manual Page 43

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Alpine DVA-9861Ri