Alpine CDA-7998 Owner's Manual download pdf (Page 53)

51-EN

1 Antenna Receptacle

Connect to the supplied ISO antenna convertor plug.

2 Audio Interrupt In Lead (Pink/Black)

Connect this lead to the Audio Interface output of a cellular

phone which provides ground shorting when a call is

received.

3 Remote Turn-On Lead (Blue/White)

Connect this lead to the remote turn-on lead of your

amplifier or signal processor.

4 Switched Power Lead (Ignition) (Red)

Connect this lead to an open terminal on the vehicle’s fuse

box or another unused power source which provides (+) 12V

only when the ignition is turned on or in the accessory

position.

5 Power Antenna Lead (Blue)

Connect this lead to the +B terminal of your power antenna,

if applicable.

NOTE

This lead should be used only for controlling the vehicle's power

antenna. Do not use this lead to turn on an amplifier or a signal

processor, etc.

6 Choke Coil with Fuse Holder (7.5A)

7 Battery Lead (Yellow)

Connect this lead to the positive (+) post of the vehicle's

battery.

8 ISO Power Supply Connector

9 Ground Lead (Black)

Connect this lead to a good chassis ground on the vehicle.

Make sure the connection is made to bare metal and is

securely fastened using the sheet metal screw provided.

! Power Supply Connector

" Ai-NET Connector

Connect this to the output or input connector of other

product (CD changer, Equalizer, etc.) equipped with Ai-

NET.

# DC/DC Converter

NOTES

• Do not install the converter at a location subjected to water

such as under the floor mat or air conditioner. This may cause

a malfunction.

• Do not bundle the DC/DC converter cable with other audio

cables. Doing so may induce noise into your system.

• Keep the DC/DC converter away from the Antenna cables and

the rear side of the unit, otherwise noise may be generated

when receiving radio broadcast.

$ Ai-NET Cable (Included with CD Changer)

% Front Output RCA Connectors

RED is right and WHITE is left.

& Rear Output RCA Connectors

RED is right and WHITE is left.

( Subwoofer Output RCA Connectors

RED is right and WHITE is left.

) RCA Extension cable (Sold Separately)

~ Remote Control Interface Connector

To remote control interface box.

+ System Switch

When connecting a processor using Ai-NET, place this

switch in the EQ/DIV position. When no device is

connected, leave the switch in the NORM position.

NOTE

Be sure to turn the power off to the unit before changing the

switch position.

, Setting the 3WAY/2 WAY switch

Set the 3way/2way Switch according to your audio system.

- Digital Output Connector

Connect this to any other optical digital products of ALPINE.

The digital signal will be output when the CD mode is on.

The system whose frequency range is divided between

the high frequency range and the low frequency range.

The system whose frequency range is divided among

the high frequency range, mid frequency range, and

the low frequency range.

The position of switching the switch: F/R/Sub-W

Front high range

speaker (L)

Rear high range

speaker (L)

Front high range

speaker (R)

Rear high range

speaker (R)

Low range

speaker (L)

Low range speaker

(R)

The position of switching the switch: 3WAY

High range

speaker (L)

Mid range

speaker (L)

High range

speaker (R)

Mid range speaker

(R)

Low range

speaker (L)

Low range speaker

(R)

NOTES

• Use the SUB-W output to connect the unit to the Low Range speaker.

• You cannot adjust the FADER when setting to 3 WAY.

Output of this unit :

Front output Rear output SUB-W output

CDA-7998R

Amplifiers

RCA Connectors

CDA-7998R

Amplifiers

RCA Connectors

1 2 ... 48 49 50 51 52 53 54 55 56

Comments to this Manuals

No comments

Alpine CDA-7998 Owner's Manual Page 53

Comments to this Manuals

Related products and manuals for CD players Alpine CDA-7998