Alpine iXA-W407BT Datasheet download pdf (Page 38)

36-EN

Adjusting the Level

Touch [ ] or [ ] of Level, then adjust the HPF or LPF level.

Adjustable output level: –12 to 0 dB.

Adjusting the Slope

Touch [ ] or [ ] of Slope, then adjust the HPF or LPF slope.

Adjustable slope: FLAT*, –6 dB/oct., –12 dB/oct., –18 dB/oct.,

–24 dB/oct.

* FLAT can be set for the HIGH slope only when User’s is selected in

“Setting the Response Slope for the High Range Speaker (TW

Setup)” (page 33). Depending on the response characteristics of the

speaker, care should be taken when setting the response slope to

FLAT, as speaker damage may result. With this unit, a message is

displayed when the response slope for the high range speaker is set

to FLAT.

Repeat steps 3 to 4 to make adjustment to the other

bands.

• While adjusting the X-Over, you should consider the frequency

response of the connected speakers.

• About the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) system

You can switch the system mode with the 2.2ch (3WAY)/4.2ch

(FRONT/REAR/SUBW.) switch on the PXA-H100. For details, refer

to the Owner’s Manual of PXA-H100.

Storing Settings in the Memory

Adjustment or setting contents of X-Over, T.Corr and P/G-EQ can be

stored.

Contents that can be stored vary depends on the audio processor used.

Check whether the Defeat mode is OFF.

Touch [ ] of PRESET on the A.Processor list

screen.

The preset station setting list is displayed.

Touch [MEMORY] of any preset station (1 through

6).

The setting contents are stored.

• The stored contents will not be deleted even when the battery power

cord is detached.

• This operation cannot be performed when a typical equalizer setting

(e.g. POPS) is selected in

“Equalizer Presets (F-EQ)” (page 33).

Calling up the Preset Memory

Check whether the Defeat mode is OFF.

Touch [ ] of PRESET on the A.Processor list

screen.

The preset station setting list is displayed.

Touch [ ] of any preset station (1 through 6) to

select the preset memory.

• It takes a few moments to call up the preset memory.

Setting the Subwoofer

Press and hold SETUP for at least 2 seconds.

The SETUP selection screen is displayed.

Touch [ ] of Audio Setup.

The AUDIO SETUP screen appears.

Touch [ ] or [ ] of Subwoofer to set the subwoofer

ON/OFF.

Touch [ ] of Subwoofer after setting the

Subwoofer to ON.

The Subwoofer SETUP screen appears.

Setting items: Level / Phase / System / Channel

Touch [ ] or [ ] of Level to adjust the Subwoofer

output.

Setting range: 0 to 15

When the subwoofer is on, you can select either System 1 or System 2

for the desired subwoofer effect.

Touch [ ] or [ ] of System to select SYSTEM1 or

SYSTEM2.

Touch [ ] or [ ] of Phase to select 0° or 180°.

The subwoofer output phase is toggled SUBWOOFER NORMAL (0°)

or SUBWOOFER REVERSE (180°).

You can set the subwoofer output to stereo or monaural. Make sure to

set the correct output for your subwoofer type.

Touch [ ] or [ ] of Channel to select STEREO or

MONO.

Adjusting the Subwoofer Level

Setting the Subwoofer System

SYSTEM1 : Subwoofer level changes according to the main

volume setting.

SYSTEM2 : Subwoofer level change is different from the main

volume setting. For example, even at low volume

settings, the subwoofer is still audible.

Setting the Subwoofer Phase

Setting the Subwoofer Channel

STEREO: Subwoofer stereo (L/R) output

MONO: Subwoofer monaural output

1 2 ... 33 34 35 36 37 38 39 40 41 42 43 ... 72 73

Comments to this Manuals

No comments

Alpine iXA-W407BT Datasheet Page 38

Comments to this Manuals

Related products and manuals for Car media receivers Alpine iXA-W407BT