Alpine CDA-9887R Datasheet download pdf (Page 29)

27-EN

01GB05CDA-9887R.fm

ALPINE CDA-9887R 68-08564Z21-A (EN)

AUDIO is selected on the setup main menu in step 2.

Subwoofer On and Off

When the subwoofer is on, perform the steps below to adjust the

subwoofer output level.

1 In the normal mode, press AUDIO/RTN repeatedly to

select the SUBWOOFER mode.

2 Adjust the level by turning the Rotary encoder.

Setting the Subwoofer System

Select either System1 or System2 for the desired subwoofer effect.

Setting the Filter Type

Setting the Subwoofer phase

The subwoofer output phase is toggled SUBWOOFER NORMAL (0°)

or SUBWOOFER REVERSE (180°). To adjust the level, turn the

Rotary encoder.

Setting the Subwoofer Output (SUBW. Channel)

You can set the subwoofer output to stereo or monaural. Make sure to

set the correct output for your subwoofer type.

Setting the Response Slope for the High Range Speaker (TW Setup)

Depending on the response characteristics of the speaker, care should be

taken when setting the response slope of the high range speaker to

FLAT in 2.2ch (3WAY) mode (see “Adjusting and Storing the Crossover

Settings” on page 19), as speaker damage may result.

DISPLAY is selected on the setup main menu in step 2.

Changing Lighting Colour (Illumination)

Illumination TYPE 1 (Initial setting) / TYPE 2 / TYPE 3 / TYPE 4 / TYPE 5

TYPE 1 TYPE 2 TYPE 3 TYPE 4 TYPE 5

You can change the lighting colour of the following seven buttons.

SOURCE/ , BAND/TA, , , , and MultEQ.

Dimmer Control

Set the Dimmer control to Auto to decrease the illumination brightness

of the unit with the head lights of the vehicle ON. This mode is useful if

you feel the unit’s backlighting is too bright at night.

• If your vehicle should have a dimmer control for the dashboard

lights, never connect the DIMMER cable (orange) of the radio to this

dimmer control.

Audio Setting

Subwoofer ON (Initial setting) / Subwoofer OFF

SUBWOOFER BASS TREBLE BALANCE FADER

AUTO VOLUME DEFEAT VOLUME SUBWOOFER

System1 (Initial setting) / System2

System1: Subwoofer level changes according the main

volume setting.

System2: Subwoofer level change is different from the main

volume setting. For example, even at low volume

settings, the subwoofer is still audible.

L=R (Initial setting) / L/R

L=R:

Left and right speakers are adjusted equally.

L/R:

Left and right speakers are individually adjusted.

SUBW. Phase 0° (Initial setting) / SUBW. Phase 180°

SUBW. Channel Stereo (Initial setting) / Mono

Stereo: Subwoofer stereo (L/R) output

Mono: Subwoofer monaural output

TW Setup Maker’s (Initial setting) / TW Setup User’s

Maker’s: As protection from possible speaker damage, FLAT

cannot be set for the response slope of the high range

speaker in 2.2ch (3WAY) mode.

User’s: The FLAT setting is possible in 2.2ch (3WAY) mode.

Display Setting

TYPE 1: When the colour of the seven buttons is blue, the colour

of the other is green.

TYPE 2: When the colour of the seven buttons is green, the

colour of the other is green.

TYPE 3: When the colour of the seven buttons is blue, the colour

of the other is red.

TYPE 4: When the colour of the seven buttons is amber, the

colour of the other is red.

TYPE 5: When the colour of the seven buttons is red, the colour

of the other is red.

Dimmer Auto (Initial setting) / Dimmer Manual

01GB00CDA-9887R.book Page 27 Thursday, March 15, 2007 3:55 PM

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 49 50

Comments to this Manuals

No comments

Alpine CDA-9887R Datasheet Page 29

Comments to this Manuals

Related products and manuals for Car media receivers Alpine CDA-9887R