Alpine INA-W900 User Manual download pdf (Page 62)

100

101

60-EN

You can modify the equalizer settings to create a response curve more

appealing to your personal taste.

Setting item: G-EQ

Select L+R by touching [ ] of G-EQ.

When parametric EQ is set to L+R, this setting will be turned

off.

Touch [ ] of G-EQ after selecting L+R.

The G-EQ list screen appears.

Adjust the G-EQ to your preference.

Adjusting the Band

Touch [ ] or [ ] of Band to select the band to be adjusted.

Band-1 (63 Hz) / Band-2 (150 Hz) / Band-3 (400 Hz) /

Band-4 (1 kHz) / Band-5 (2.5 kHz) / Band-6 (6.3 kHz) /

Band-7 (17.5 kHz)

Adjusting the Level

Touch [ ] or [ ] of Level to adjust the level of selected

band.

Adjustable output level: –6 to +6 dB

To adjust another band, repeat step 3, and then

adjust all bands.

• When graphic EQ is adjusted, the adjustment for parametric EQ

becomes ineffective.

You can change the unit, (cm or inch) of time correction.

Touch [ ] or [ ] of T.Corr Parameter to select cm or Inch.

Setting item: T.Corr Parameter

cm Inch

Before performing the following procedures, refer to “About Time

Correction” (page 62).

Setting item: T.Corr

Touch [ ] of T.Corr.

The T.Corr adjustment screen appears.

Adjust the distance (0.0 to 336.6 cm) of a desired

speaker by touching the respective [

] or [ ]

button.

L = (distance to farthest speaker) – (distance to other

speakers)

Refer to “Time Correction Value List” on page 62.

Repeat step 2 to set another speaker.

Set these values to achieve simultaneous sound

propagation to the listening position from all speakers.

Before performing the following procedures, refer to “About the

Crossover” (page 63).

Setting item: X-Over

Touch [ ] or [ ] of X-Over to select L+R or L/R.

Touch [ ] of X-Over.

A speaker list on the X-Over screen is displayed.

Touch [ ] of the band to be adjusted.

The screen changes to the X-Over screen to be adjusted.

4.2ch (FRONT/REAR/SUBW.) System / (L+R)

Setting contents:

Low (SUB-W) / Mid (REAR) / High (FRONT)

4.2ch (FRONT/REAR/SUBW.) System / (L/R)

Setting contents:

Low (SUB-W)-L / Low (SUB-W)-R / Mid (REAR)-L /

Mid (REAR)-R / High (FRONT)-L / High (FRONT)-R

Adjust the crossover to your preference.

Selecting the Cut-Off Frequency

Touch [ ] or [ ] of Freq., then select the cut-off frequency

(crossover point).

The adjustable bandwidth differs depending on the speaker

(channel).

4.2ch (FRONT/REAR/SUBW.) System

Setting contents:

Low (SUB-W) 20 Hz~200Hz

Mid (REAR) 20 Hz~200Hz

High (FRONT) 20 Hz~200Hz

Adjusting the Slope

Touch [ ] or [ ] of Slope, then adjust the HPF or LPF slope.

Adjustable slope: FLAT, –6 dB/oct., –12 dB/oct., –18 dB/oct.,

–24 dB/oct.

Adjusting the Level

Touch [ ] or [ ] of Level, then adjust the HPF or LPF level.

Adjustable output level: -12 to 0 dB.

Repeat steps 3 to 4 to make adjustment to the other

bands.

2.2ch (3WAY) System / (L+R)

Setting contents:

Low / Mid-L / Mid-H / High

2.2ch (3WAY) System / (L/R)

Setting contents:

Low-L / Low-R / Mid-L-L / Mid-L-R / Mid-H-L /

Mid-H-R / High-L / High-R

Adjusting the Graphic Equalizer Curve

(G-EQ)

Setting the Time Correction Unit (T.Corr

Parameter)

cm: The unit of time correction is cm.

Inch: The unit of time correction is Inch.

Adjusting the Time Correction (T.Corr)

Adjusting the Crossover Settings (X-OVER)

L+R: Sets the same adjustment values for the left and right

channels.

L/R: Different adjustment values can be set for the left and

right channels.

4.2ch (FRONT/REAR/SUBW.) System

2.2ch (3WAY) System

1 ... 61 62 63 ... 101

Comments to this Manuals

No comments

Alpine INA-W900 User Manual Page 62

Comments to this Manuals

Related products and manuals for Car speakers Alpine INA-W900